Corrosion fatigue of extruded magnesium alloys

Corrosion fatigue tests were carried out on extruded AZ31 (3% Al, 1% Zn, 0.3% Mn, Mg—the rest), AM50 (5% Al, 0.4% Mn, Mg—the rest) and ZK60 (5% Zn, 0.5% Zr, Mg—the rest) Mg alloys in air, NaCl-based and borate solutions. N_sol/N_air ratios (the relative fatigue life) were used for the analysis of the corrosion fatigue behavior of Mg alloys in various environments, where N_sol and N_air are the numbers of cycles to failure in the solution and in air, respectively. Extruded ZK60 alloy reveals very high fatigue and corrosion fatigue properties in comparison with other alloys. However, it has the lowest relative fatigue life (N_sol/N_air 10⁻³–10⁻²) or the highest sensitivity to the action of NaCl-based solutions in comparison with that of AM50 and AZ31 alloys (N_sol/N_air 10⁻²–10⁻¹). Under the same stress, the corrosion fatigue life of extruded alloys is significantly longer than that of die-cast alloys (N_sol for extruded AM50 in NaCl is two to three times longer than that of die-cast AM50).     

On the specific reactivity of platinum segregated layers on Pt80X20 (111) (X= Ni,Co, Fe) alloys

The influence of alloying of Pt with 20 at.% of Ni, Co and Fe has been studied in the hydrogenation of 1,3 butadiene. Iron induces the more important modifications, with both higher activity and selectivity. The results are discussed in terms of the surface segregation, the local order in surface and the electronic properties measured by photoemission of core levels.     

高强度钢的Zn—Ti合金新镀层

本文研究了一种Ｚｎ－Ｔｉ合金新镀层，经盐水浸泡、中性盐雾和大气暴露试验结果试验，其耐蚀明显超过镀Ｚｎ层，并与镀Ｃｄ层相近，用缺口持久拉伸试验检验氢脆性，拉伸持续时间超过２００ｈ，达到原航空部部颁标准（ＨＢ５０６７－８５），该镀层适用于高强度钢防护。     

Electrical characterization of waterside corrosion films formed on ZrNb(1%)O(0.13%)

Oxide films formed by water oxidation at 360°C on ZrNb(1%)O(0.13%) for several durations (50-300 days) were studied by impedance spectroscopy (IS) in gaseous atmosphere. The electrical behavior of oxide layers was investigated as a function of the temperature (25-300°C) at constant oxygen partial pressure (0.3 Pa). Cole-Cole diagrams suggest a frequency-temperature equivalence. A simple electrical model has been derived from the as-deduced 14 decade master curve. Equivalent circuit includes a series association of two layers exhibiting different dielectric properties: a dense layer near the oxide-metal interface and a porous layer at the waterside. Electronic conductivity is predominant within the whole temperature range, but ionic contribution was proposed to increase for temperature higher than 170°C. During the parabolic oxidation step, the oxide thickness of the barrier layer increases but oxide growth would not be only a geometrical one. The kinetic modification to a constant oxidation rate was observed to be correlated to the increase of the dense layer thickness. Such a behavior suggests that the mechanism controlling oxidation rate is not a pure mechanism of oxygen diffusion through this layer. Finally, a qualitative model of activated electrons transport based on an hopping mechanism was proposed in order to take into account that the Arrhenius diagrams of both total conductivity and dispersion factor are characterized by a break point with two activation energy values.     

Mössbauer Study of the Influence of Fe-Si-N Liquid in the Synthesis of β-Si3N4 from Silica

Mössbauer spectra of the products obtained by carbothermal reduction and distribution of silica in the presence of iron in the temperatures range 1200^o to 1540^o were studied. The preponderance of β- Si₃N₄ over the α form at a higher reaction temperature were assumed to be related to the formation of an Fe-Si-N liquid. The liquid did not alter its composition with the variation of reduction-temprature, Iron had no effect on the reaction mechanism below 1300^oC.     

熔融 NaCl-(Na,K)_2SO_4引起的 Fe-Cr 合金的热腐蚀

本文采用电化学方法研究了 Fe-Cr 合金在800℃、熔融 NaCl-(Na,K)_2SO_4中的腐蚀行为,并对腐蚀产物进行了观察和分析。结果表明,提高合金 Cr 含量可以改善合金耐蚀性能。氧化-硫化是Fe5Cr、Fe10Cr 合金腐蚀破坏的主要方式;氧化膜的熔融反应是 Fe20Cr、Fe25Cr 合金加速腐蚀的主要原因。同时,氧化膜的机械破裂也加速了合金的腐蚀。     

Color characteristics of Cu-Zn-Al alloys

ＣＯＬＯＲＣＨＡＲＡＣＴＥＲＩＳＴＩＣＳＯＦＣｕ－Ｚｎ－ＡｌＡＬＬＯＹＳ￣①Ｌｉ，Ｂａｏｍｉａｎ；Ｚｈａｎｇ，Ｘｉｕｈｕａ（ＳｈｅｎｙａｎｇＩｎｓｔｉｔｕｔｅｏｆＧｏｌｄＴｅｃｈｎｏｌｏｇｙ，Ｓｈｅｎｙａｎｇ１１００１５）ＣＯＬＯＲＣＨＡＲＡＣＴＥＲ...     

机械合金化CuRECr合金的显微组织结构及性能分析

利用机械合金化和真空烧结技术制备CuRECr25和CuRECr50合金，讨论了机械合金化不同球磨时间、球料比等工艺参数对合金显微组织结构、物理机械性能，含氧量、含氮量等的影响，并且与CuCr25、CuCr50合金进行了物理机械性能比较。研究结果表明：CuRECr合金组织均匀、细微，具有强度、硬度高等特点，为改进CuCr系电真空接触材料开辟了新途径。